Bollinger delivers FRC Rollin Fritch to Coast Guard
AUGUST 23, 2016 — Bollinger Shipyards, Lockport, LA, has delivered the USCGC Rollin Fritch, the 19th Fast Response Cutter (FRC) to the United States Coast Guard. The Coast Guard took delivery of
AUGUST 23, 2016 — Bollinger Shipyards, Lockport, LA, has delivered the USCGC Rollin Fritch, the 19th Fast Response Cutter (FRC) to the United States Coast Guard. The Coast Guard took delivery of
JULY 11, 2016—NAVSEA has awarded four U.S. shipyards — Bollinger Shipyards Lockport, Eastern Shipbuilding Group, Fincantieri Marine Group, and VT Halter Marine — Phase 1 design study contracts, worth just under $200,000
JUNE 22, 2016 — Bollinger Shipyards, Lockport, LA, has delivered the USCGC Joseph Tezanos, the eighteenth Fast Response Cutter (FRC) to the United States Coast Guard. The Coast Guard took delivery of
Last year, the agency announced that it would order a new series of vessels—up to 37 in total for about $450 million— known as the Maneuver Support Vessel (Light), MSV(L) for its watercraft fleet. At print time, no RFP had been released, but it is expected to be issued in the next few weeks. The Army currently has a fleet of 132 vessels that perform a large percentage of the U.S. forces’ equipment and supply deliveries. Missions for the fleet are broken up into four categories: (1) Landing Craft; (2) Ship-to-Shore Enablers; (3) Towing and Terminal Support Operations; (4) Watercraft Operations Support.
The U.S. Army’s fleet is meant to be deployed worldwide, and can support operational movement and maneuver and force repositioning. Additionally, the agency says, the vessels perform a variety of roles.
Vessel type is broken up into two categories:
Details on the MSV(L)
The upcoming MSV(L) will replace the Landing Craft Mechanized 8 (LCM-8) (pictured above), which has been in service since 1967. The LCM-8 travels at 12 knots with no load and 8 knots or less with load. The LCM-8 is small in size, measuring just 74 ft x 21 ft, and can be used in confined areas. It has a range of 332 nautical miles unloaded and 271 nautical miles loaded. Designed for operations in rough waters, the LCM-8 can maneuver through sea state 3, breakers and can ground on a beach. Its bow ramp enables roll-on / roll-off (RO/RO) operations with wheeled and tracked vehicles.
The MSV(L) will feature an increased payload and speed over its predecessor, LCM-8.
The introduction of the MSV(L) into the fleet, says the Army, “will enable the agency to meet its movement, maneuver, and integrated expeditionary sustainment requirements with a more agile, versatile; and capable platform. The MSV(L) will conduct movement and maneuver of tactical force elements as well as traditional Army Watercraft System sustainment operations.”
The MSV(L) will also be able to operate in a variety bodies of waters including coastal waters, rivers and narrow waterways.
According to the agency, Col. Michael M. Russell Sr. Army G-8 FD Division Chief, called the MSV(L) program a lynchpin to the Army’s watercraft strategy. The landing craft will have the ability and capacity to carry a tank, a Joint Light Tactical Vehicle (JLTV), a Stryker armored fighting vehicle, troops, or supplies.
Russell added that the system would not be designed from scratch, and will likely be based on an existing design that will be “ruggedized” and made to fit the Army’s mission profile.
Industry Players Express Interest
One of the designs expected to be in the running is Constructions Industrielles de la Méditerranée’s (CNIM) L-Cat design.
Last December it was announced the CNIM would team up with Fincantieri Marine Group (FMG), the U.S. subsidiary of Fincantieri, Oshkosh Defense, LLC, and Watercraft Logistics Services (WLS) to pursue the contract.
The L-Cat (Landing Catamaran Craft) is an innovative and rapid amphibious ship with a RO/RO design that integrates a mobile loading platform in a catamaran hull. This enables for personnel, armored vehicles and equipment to be unloaded in areas where there are no port facilities and shallow waters.
Intended for shore-to-shore applications, the L-Cat is already successfully used by the French National Navy, under the name EDA-R.
CNIM says that “during amphibious operations, it (the L-Cat) guarantees optimal transit speed, rapid loading and unloading of the deck.” This helps reduce threat during exposure time and offers a high degree of autonomy, with the vessel able to operate in a rage of 500 to 700 nautical miles, depending on the load.
Measuring 30 m x 12.6 m, the L-Cat has a maximum payload capacity of 100 tonnes, can reach speeds of up to 30 knots when empty and 18 knots when loaded to maximum payload.
The design’s proven track record, along with its own successful history of building vessels for the Army, Coast Guard and Navy, makes the group the optimal choice for the MSV(L) build program, according to Francesco G. Valente, President and CEO of FMG. “We believe that our world-class team and proven design represent the lowest risk and lowest total life-cycle cost to the U.S. Army,” said Valente.
Valente notes that FMG shipyards—Fincantieri Marinette Marine, Fincantieri Bay Shipbuilding and Fincantieri Ace Marine—have experience in building these types of landing craft, having built the LCM-6, LCM-8 and LCU landing craft in Marinette. The shipbuilder has also had the distinction of building 562 landing craft for the Army and Navy over a period of 23-years. And Marinette Marine was also half of the RB-M team (Kvichak Industries the other half) that built the Response Boat-Medium for the U.S. Coast Guard.
Meeting Production Needs, Who Wants In?
According to the Army’s MSV(L) DRAFT-Production Schedule, it is expected that one prototype will be built and tested by FY19, four will be built during Low Rate Initial Production (LRIP) between FY 21 and FY 22; and, should the program reach full scale production, 32 will be produced during a four-year period between FY23 through FY27.
Kvichak, formerly known as Kvichak Marine Industries, now part of the Vigor group of companies, could also be a contender should it choose to pursue the contract.
The boat builder is listed on the Army’s list of Interested Prime Contractors along with Bollinger Shipyards, Conrad Shipyards, Ingalls Shipbuilding, Derecktor, Sterling Shipyard, Swiftships, LLC, and United States Marine, Inc.—the list is a prime example of the variety of yards interested in the contract, as well as the agency’s willingness to open up the contract pursuit to all shipyard types.
Kvichak is no stranger to producing vessels for government agencies in a full-scale production cycle, having long been a builder of pilot and patrol boats. Most notably, Kvichak was the other half of Team RB-M. The team built and delivered 174 RB-Ms for the Coast Guard, on time and on budget, completing the program in 2015.
The other builders on the list also have diverse portfolios, making each a feasible choice for the MSV(L) program.
Bollinger has long been a builder of patrol vessels for both the U.S. Coast Guard and U.S. Navy. Most recently delivering the 17th Fast Response Cutter to the U.S. Coast Guard.
Conrad has, perhaps, the most diverse portfolio, with experience in the construction, conversion and repair of a wide variety of steel and aluminum marine vessels across its shipyards for both commercial and government customers—Conrad’s Orange shipyard has produced a number of vessels for the army. Conrad, as most are aware, is currently building the first LNG bunker barge for operation in U.S.
Derecktor could put itself back in the shipbuilding game big time, should it win this contract. The yard has seen its share of trouble over the last decade, having filed for bankruptcy in Connecticut and losing its Bridgeport facility in the process, but Derecktor is putting in the work to get itself to the level it once was. The builder has experience building a variety of innovative vessel types both in the commercial and private yacht sector, including ferries, security vessels, patrol crafts, research vessels and workboats.
Ingalls Shipbuilding, a division of Huntington Ingalls Industries, has an extensive history with both the Coast Guard and Navy. Ingalls is currently building vessel 6 through 8 in the National Security Cutter Program for the Coast Guard’s fleet at its Pascagoula, MS shipyard. Under the program, eight vessels will be built to replace the aging 378-ft high endurance cutters. The shipbuilder also recently announced that the U.S. Navy’s 10th San Antonio-class amphibious transport dock, John P. Murtha (LPD 26), successfully completed acceptance trials. Under its contract with the Navy, Ingalls has built and delivered nine ships in the San Antonio Class. LPD 26 will be delivered in May. The 11th LPD, Portland (LPD 27) will be christened later this month. The yard has also received advanced procurement funding for long-lead-time material for the 12th ship in the series, the LPD 28.
Texas-based Sterling Shipyard, started by Harry Murdock and Brad Taylor, formerly of Orange Shipbuilding, has built a number of tank barges and towboats.
Swiftships specializes in the construction of small to medium-sized vessels made with steel, aluminum and fiberglass. It has delivered boats to the U.S. military, both commercial and private companies and 52 foreign countries.
United States Marine, Inc., Gulfport, MS, a designer and builder of fast patrol and special operations craft for the U.S. and foreign militaries, has predominately been a builder of military, patrol and special warfare boats in the 21 ft to 90 ft range. In its 30 plus years in business it has delivered over 500 craft to the U.S. Navy, USSCOCOM, NAVSEA and foreign militaries.
MAY 4, 2016 —In Phase 2 of its FRC acquisition program, the U.S. Coast Guard today awarded a contract to Bollinger Shipyards LLC, Lockport, LA, for the procurement of up to 26
Nichols Brothers Boat Builders recently completed sea trials on the second of 10,000 hp oceangoing tugs for Kirby Offshore Marine, the coastal tug and barge arm of Kirby Corporation, Houston, TX. The 136 ft x 44 ft tug, Tina Pyne, will be connected to the 185,000 bbl ocean tank barge 185-02 built by Gunderson Marine, Portland, OR.
Kirby’s newbuild plan also includes two 155,000 bbl/6,000 hp Articulated Tug Barge (ATB) units under construction at Fincantieri Bay Shipbuilding in Sturgeon Bay, WI, as well as two 120 ft x 35 ft, 4,894 hp tugs being built by Nichols Brothers Boat Builders. Each tug will be powered by two Caterpillar 3516C engines, each rated at 2,447 hp at 1,600 rev/min, with Reintjes reduction gears turning two Nautican fixed-pitched propellers with fixed nozzles. The Reintjes gears were supplied by Karl Senner, LLC, Kenner, LA. The tugs will also have two C7.1 Caterpillar generators for electrical service. Selected deck machinery includes one TESD-34 Markey tow winch, one CEW-60 Markey electric capstan, and one Smith Berger Tow Pin.
Kirby Offshore Marine is the largest U.S. operator of coastal tank barges that provide regional distribution of refined petroleum products, black oil and crude oil. Kirby grew its coastal marine transportation business through the acquisition of K-Sea Transportation Partners L.P. back in 2011 in a transaction valued at about $604 million. At that time, Kirby acquired 58 tank barges (only 54 were double hull) with a capacity of 3.8 million barrels and 63 tugs.
Already the operator of the largest inland tank barges and towboats, Kirby Corporation will grow further with the purchase of Seacor Holdings Inc.’s inland tank barge fleet for about $88 million in cash.
Under the terms of the deal struck last month, Kirby will acquire 27 inland 30,000 bbl tank barges and 13 inland towboats, plus one 30,000 bbl tank barge and one towboat currently under construction. As part of the agreement, Kirby will transfer to Seacor the ownership of one Florida-based ship-docking tugboat.
Kirby Inland Marine currently has 898 active inland tank barges and 243 towboats, with a total carrying capacity of 17.9 million barrels. The primary cargoes transported by this fleet are chemicals, petrochemical feedstocks, gasoline additives, refined petroleum products, liquid fertilizer, black oil and pressurized products.
Kirby President and CEO David Grzebinski, says “Operating primarily in the refined products trade, these assets will be complementary to our existing fleet and will allow us to continue to enhance customer service.”
TRIPLE-SCREW BOATS FOR MID-RIVER
Over the years, Rodriguez Shipbuilding, Inc.’s triple-screw towboats have won a following operating in the shallow waters where the Mississippi River meets the Gulf of Mexico. These Lugger-type vessels are designed with a distinctive aft-cabin.
Mid-River Terminals of Osceola, AR, recently took delivery of a new design towboat from Rodriguez Shipbuilding, Coden, AL. With a conventional forward-house pusher configuration, the new 70 ft x 30 ft MV/ Dianna Lynn uses the same propulsion as the Lugger tugs. This is composed of three in-line six-cylinder Cummins QSK 19 engines, each delivering 660 hp. Each engine turns a 66-inch stainless steel propeller through ZF gears with 6:1 reduction ratio. The combination gives the 1,980 hp towboat an eight-foot operating draft.
Fitted with large windows, the wheelhouse has a full 360-degree view and is set atop two accommodation decks and a half deck that also serves for bridge electronics support. This gives the towboat a 31-foot high eye-level, with full tanks, for working high barges.
Steering and flanking rudders are controlled by wheelhouse levers with mechanical shafts through the houses and connected to the hydraulic actuator valves in the upper engine room.
A set of push knees and deck winches with cheek blocks facilitates barge work. A pair of 55 kW gensets meets the boat’s electrical requirements.
Zero discharge tanks, built integral to the hull, provide storage for treated sewage and all drains. A separate tank handles waste oil.
The M/V Dianna Lynn is the fourth boat in the Mid-River Terminal fleet, all of which are Cummins powered. Owner Rick Ellis said, “We wanted the three engines for redundancy so that even if we loose an engine we still have over 1,200 horsepower.”
The new boat will be primarily involved in fleeting and harbor work, “Rodriguez did a great job and it is a great handling boat,” Ellis added.
BOUCHARD, MORAN EXPANDING FLEETS
As we highlighted last month, Bouchard Transportation’s multi-million-dollar newbuild program is winding down. The Melville, NY, owner is completing the construction of two new 6,000 hp, 310 ft x 38 ft Intercon tugs at VT Halter Marine, Pascagoula, MS. The tugs Morton S. Bouchard Jr. and Fredrick E. Bouchard will be connected to the B. No. 210 and B. No. 220. The two tank barges were the first double hull tank barges built by Bouchard,. Both were built as wire barges, but following their conversion and stretch at Bollinger Shipyards, Inc., both will be Intercon, flat deck double hulls capable of carrying 110,000 bbl of oil.
Moran Towing, New Canaan, CT, expects to take delivery shortly of a 5,300 hp/110,000 bbl ATB unit from Fincantieri Bay Shipbuilding. The Sturgeon Bay, WI, has another 8,000hp/155,000 bbl ATB unit under construction for Plains All American Pipeline, with an option for a second unit, and signed a hotly contested order for another 8,000 hp/185,000 for another earlier last month. That contract includes an option for another.
The new barge will have a capacity of 185,000-barrels with dimensions of 578 feet by 78 feet. The tug will be an 8.000-HP unit equipped with Tier 4 engines—believed to be GE Marine—to meet the latest EPA emission standards.
When complete, the ATB will operate on the U.S. East Coast and Gulf of Mexico.
“We are pleased to have this opportunity,” said Francesco Valente, FMG President and CEO. “This new contract marks an additional expansion of our product portfolio, confirms our ability to win business with new customers in a very competitive market and further consolidates our presence and reach in the U.S. market.”
“This award increases our pipeline of new construction to 10 vessels and provides additional stability to our business,” said FBS Vice-President and General Manager, Todd Thayse. “We are grateful for the confidence that our customers continue to place in our reputation for quality and the strong shipbuilding skills of our workforce.”
Conrad Shipyards, Morgan City, LA, meanwhile, is building the 80,000 bbl ATB unit for John W. Stone, as well as two ATB tugs for Harley Marine Services, Seattle, WA. Conrad Orange Shipyard in Orange, TX, recently delivered the 35,000 bbl Double Skin 315 to Vane Brothers Company. That barge was towed to New York by the Elizabeth Anne, the first in a series of eight 4,200 hp tugs being built by St. Johns Ship Building, Palatka, FL.
Designed by Frank Basile, P.E. of Entech Designs, LLC, the Elizabeth Anne Class tugboat is a close cousin to Vane’s Basile-designed Patapsco Class tugboats, 15 of which were produced between 2004 and 2009. Measuring 100 feet long and 34 feet wide, with a hull depth of 15 feet, the model-bow Elizabeth Anne utilizes two Caterpillar 3516 Tier 3 engines, each generating 2,100 hhp at 1,600 rev/min. Two John Deere PowerTech 4045, 99 kW generators deliver service power to the boat, while a third John Deere 4045 teamed with an Allison transmission drives the chain-driven INTERCON DD200 towing winch.
ROBERT ALLAN’S LATEST
Over the years, world renowned naval architectural and marine engineering firm Robert Allan Ltd. Has successfully teamed with shipyards around the world to bring new innovative tug designs to the market. Its latest is the VectRA 3000 Class Tug, a high performance VSP Tractor tug designed by Robert Allan Ltd in close collaboration with Turkish ship builder Sanmar and Voith Turbo Propulsion. The tug is designed for maximum efficiency in the performance of towing, harbor ship-handling and escorting of large ships. Performance has been verified with extensive model tests at the commencement of the design cycle. The unique propulsion arrangement features high-speed diesel engines connected to the Voith units via reduction gearboxes with integral clutches. With a bollard pull of 70 tonnes, the VectRA 3000 form can generate escort steering forces in excess of 100 tonnes. Additionally, the design has fire-fighting and oil recovery capabilities and is fully MLC compliant.
The VectRA 3000 has been designed exclusively for Sanmar to offer as one of its highly successful stable of progressive tugboats for the world market.
The first vessel in the series, the M/T Ares, built for Italian tugowner Tripmare SpA, was successfully launched at Sanmar’s new Altinova advanced shipbuilding facility this past February.
The tug has an overall length of 30.25 m, beam of 13m, depth of 5.1m, and design draft of 6.1m.
The vessels are built and classed to the following ABS notation: ✠ A1 Towing Vessel, Escort Vessel, ✠ AMS, Unrestricted Service, UWILD, HAB (WB), ABCU Fire-Fighting Vessel Class 1 Oil Spill Recovery – Capability Class 2 (>60° C) (OSR – C2).
Rather uniquely for a VSP installation, the propulsion drivetrain comprises two Cat 3516C high-speed diesel engines, each rated 2,525 kW at 1,800 rev/min, and driving Voith 32R5EC/265-2 cycloidal propellers. The engines are connected to the Voith drives through a pair of Reintjes WAF 863 gearboxes and Vulkan composite shafts, rather than using the more traditional turbo coupling. This combination is smaller, lighter and less costly than the traditional medium speed drive system. The electrical plant consists of two identical diesel gensets, each with a rated output of 86 ekW.
Crew accommodations are all located on the main deck level for optimal crew comfort. There are 4 single crew cabins plus 1 double crew cabin, each with an en-suite bathroom. A comfortable lounge/mess area and galley facilities are also in the deckhouse, with galley stores and laundry room located below the main deck forward.
All towing, ship handling, and escort work is performed using a double drum escort winch and escort rated staple fitted on the aft deck. One drum can store 710 meters of steel wire line, while the other stores 150 meters of synthetic towline. For increased operational flexibility radial type tow hooks are installed on the main deck forward and aft.
As in a traditional tractor configuration, the stern is the working end of the tug, and as such features heavy-duty cylindrical fendering with a course of ‘W’ fenders below. Hollow ‘D’ fenders protect the sheer lines and tie neatly into the ‘W’ fenders at the bow.
The wheelhouse is designed for excellent 360-degree visibility and includes overhead windows. The split type console is biased aft to ensure unobstructed visibility of the working deck (including the winch, staple, bulwarks and fenders) during operations.
CARGILL’s PUSHBOATS FOR THE AMAZON
In Brazil, the construction of a fleet of Robert Allan Ltd.-designed pushboats and barges for Cargill Transportation is nearing completion. To be used for transporting grain products on the Amazon River system, the fleet includes two shallow-draft RApide 2800-Z2 class pushboats built at INACE in Fortaleza, Brazil and 20 hopper barges built at Rio Maguari in Belem, Brazil.
Each of the two new RApide 2800-Z2 Class pushboats are 28m x 10.5m, with a minimum operating draft of 2.2m and normal operating draft of 2.5m. The two sister vessels, the Cargill Cachara and Cargill Tucunare, are designed to push barge convoys on the Amazon River system.
During the early phases of design, extensive CFD simulations were undertaken to optimize the pushboat’s hull shape to minimize total convoy resistance.
This work was completed in conjunction with extensive logistics modeling of the transportation system to optimize the selection of vessels for the desired route and to analyze operational drafts and cargo throughput at various river levels.
The pushboats were designed to ABS and Brazilian NORMAM-02 requirements and are outfitted to the highest standards.
The wheelhouse is designed for maximum all-round visibility with a split forward control station providing maximum visibility to the foredeck working area of the tug as well as to the convoy of barges ahead. Accommodation for up to 13 people is provided onboard and a large galley and mess is provided on the main deck.
The deckhouse extends aft over the main propulsion components, which comprise a pair of Caterpillar 3512B diesel engines, driving Schottel SRP 550 Z-drive units. The drives are fitted in tunnels designed to optimize flow while reducing draft. Two identical Caterpillar diesel gensets are provided in the vessel’s auxiliary machinery space located below the main deck.
The corresponding 61m x 15m box and rake barges were designed by Robert Allan Ltd. to ABS River Rule requirements. Additional extensive FEA analysis of the structure was performed in order to optimize the design for minimum steel weight while ensuring long service life during river operations. Sliding aluminum hatch covers have been supplied to ensure the cargo stays dry at all times.
Each FRC is named for an enlisted Coast Guard hero who distinguished him or herself in the line of duty. This vessel is named after Coast Guard Hero Winslow Griesser.
Winslow W. Griesser, Keeper of the Buffalo Life-Saving Station in New York, was awarded the Gold Lifesaving Medal on February 23, 1901 for his heroic actions during a dramatic rescue on November 21, 1900.
“We are very pleased to announce the delivery of the latest FRC built by Bollinger Shipyards, the Winslow Griesser, to the 7th Coast Guard District in Puerto Rico,” said Bollinger President & CEO, Ben Bordelon. “We are looking forward to honoring and celebrating the heroic acts of Winslow Griesser at the vessel’s commissioning.”
To build the Coast Guard’s Sentinel-class FRC program, Bollinger Shipyards uses a proven, in-service parent craft design based on the Damen Stan Patrol Boat 4708. It has a flank speed of 28 knots, state of the art command, control, communications and computer technology, and a stern launch system for the vessel’s 26 foot cutter boat. The FRC has been described as an operational “game changer,” by senior Coast Guard officials.
The False Claims Act suit alleges that Bollinger misrepresented the longitudinal strength of patrol boats it delivered to the Coast Guard that resulted in the boats buckling and failing once they were put into service. Bollinger Shipyards is located in Lockport, Louisiana.
“Those who expect to do business with the government must do so fairly and honestly,” said Principal Deputy Assistant Attorney General Benjamin Mizer, head of the Justice Department’s Civil Division. “We expect the utmost integrity and reliability from the contractors that design and build equipment that is essential to public safety and our national defense.”
In 2002, the U.S. Coast Guard contracted to lengthen the Coast Guard’s existing fleet of 110-foot patrol boats to 123 feet and to make other modifications. Bollinger was the subcontractor that performed the 123-foot patrol boat design and conversion work. An essential element of the conversion was that the modified boats have sufficient longitudinal strength to meet the performance requirements set forth in the contract.
The United States alleged Bollinger provided the Coast Guard with engineering calculations that falsely represented the longitudinal strength of the boats and was two times greater than their actual longitudinal strength. The United States alleged Bollinger ran the calculations three times and only provided the Coast Guard with the highest and most inaccurate, of the three calculations. The United States further alleged Bollinger also failed to follow the quality control procedures that were mandated by the contract that would have ensured against such engineering miscalculations.
The case was handled jointly by the Civil Division’s Commercial Litigation Branch and the U.S. Attorney’s Office of the Eastern District of Louisiana.The claims resolved by the settlement are allegations only, and there has been no determination of liability.
MAY 21, 2015—Long-time Bollinger Shipyards executive Scott J. Theriot has joined Conrad Industries, Inc., Morgan City, LA, as its Executive Vice President and Chief Operating Officer. “We are excited to have Scott
MARCH 19, 2015—Marine assurance provider and consulting services company Baker Marine Solutions, Covington, LA, has appointed Robert Socha as Vice President Business Development for the U.S. and international operations of the company.